Old Skool - 21' Daytona

[Joker]

Tom Cowle's 21' Daytona is out on the rigging floor and will be heading to GS Marine soon for the pump modifications.
Ordering all the gauges, etc. next week and will start cutting holes when Greg sends it back.

What's a 21 going for?

 

[rush1]

Straight Outta iliminator
Badd ass saw it on instagram today and had to check it out that is a work of art :thumbsup

 

[LAVEYNICK]

updates?

 

[shueman]

Updates:

Dash, Helm, Trim, etc. Should be leaving for B1 Racing next week sometime, then on to Phoenix for the motor install.

 

[AZMIDLYF]

Who is doing the motor in Phoenix?

 

[shueman]

Who is doing the motor in Phoenix?

Actually the customer's brother ...

 

[Joker]

What's a 21 going for?

Any answers

 

[shueman]

Any answers

This one is $60k SANS motor and pump ... yep, that much these days.

Bare white hull and fuel tanks ... $28k.

 

[Joker]

This one is $60k SANS motor and pump ... yep, that much these days.

Bare white hull and fuel tanks ... $28k.

Thank you.[emoji106]

 

[Joker]

This one is $60k SANS motor and pump ... yep, that much these days.

Bare white hull and fuel tanks ... $28k.

Damn, I remember buying a new one in 98 for 28k

 

[rivrrts429]

Damn, I remember buying a new one in 98 for 28k

I saw it today. It's going to be one bad ass boat. Damn near left a deposit with Gary [emoji2]

 

[shueman]

I saw it today. It's going to be one bad ass boat. Damn near left a deposit with Gary [emoji2]

When your ready, we'll put something on paper and then go arm wrestle Leach for his "special price"

Thanks again for stopping by and giving us your support, much appreciated.

 

[shueman]

Boat is on the trailer and off to B1 Racing for the pump install ...

 

[Joker]

I loved the front but that rub rail or whatever u call it in the back just kills it. Is there a cleaner option?

 

[rivrrts429]

I loved the front but that rub rail or whatever u call it in the back just kills it. Is there a cleaner option?

Agreed, it needs to be capped. It's a night and day difference when the 21's have the rail deleted in front and back.

 

[Joker]

Agreed, it needs to be capped. It's a night and day difference when the 21's have the rail deleted in front and back.

My old 21 had it, outlaw bought it and deleted it and it was a huge difference.

 

[rivrrts429]

My old 21 had it, outlaw bought it and deleted it and it was a huge difference.

That was your old 21', with the flames? That was a nice boat.

 

[Joker]

That was your old 21', with the flames? That was a nice boat.

Yup,
Paul did a nice job with it once he bought it.[emoji106]

 

[shueman]

I'm totally in favor of capping ... just a pricey option these days ...:grumble:

 

[Gelcoater]

Yup,
Paul did a nice job with it once he bought it.[emoji106]

Probably one of if not the best build thread I have seen here.:thumbsup

 

[Joker]

I'm totally in favor of capping ... just a pricey option these days ...:grumble:

I'm far from an expert, but what's entailed in capping?
I'm not sure what the terminology means.

 

[Gelcoater]

I'm totally in favor of capping ... just a pricey option these days ...:grumble:

Personally,I'm not.
Never been a fan of cutting into and patching perfectly good Gelcoat.

When I learned this trade the goal was to have the boat come out needing no gel repair.
Now we do repair on purpose:rolleyes

 

[Gelcoater]

I'm far from an expert, but what's entailed in capping?
I'm not sure what the terminology means.

Check out the 36 Speedster thread for visual aids.
Basically after the deck and hull are joined they grind into that seam.Then fill it with glass,grind that fill smooth,then regelcoat over it.
The bitch is,and where the talent comes into play for the repair guy is blending in that new(external gel) which is now on top to the gel that was shot in the mold during the build.Getting that blend to be seamless.

 

[Joker]

Check out the 36 Speedster thread for visual aids.
Basically after the deck and hull are joined they grind into that seam.Then fill it with glass,grind that fill smooth,then regelcoat over it.
The bitch is,and where the talent comes into play for the repair guy is blending in that new(external gel) which is now on top to the gel that was shot in the mold during the build.Getting that blend to be seamless.

Thank you

 

[RCDave]

Can stainless rub rail work on this boat? Perhaps not with the complex angles on the back.

Or rub rail absent the screws?

I'd be paranoid docking or tieing up with a capped boat. Not sure it would be practical for me. But the work and talent you gel artists do in and out of the mold blows my mind

 

[RCDave]

Any updates? Pics?

 

[shueman]

Any updates? Pics?

It's been at B1 Racing for a few weeks, then off to AZ for the engine install.
Owner picked up the motor harness and said it should be back to the shop for interior in ... 2 weeks. :thumbsup

 

[UAV.Pilot]

I'm far from an expert, but what's entailed in capping?
I'm not sure what the terminology means.

This is an example of partial capping on my Daytona..I personally thought it was a clean job, but it's a basic one color, I could only imagine if it was a typical Eliminator 5 to 7 color combo.
Just the front and rear are done, with a one piece stainless rub rail down he side. Clean

 

[Outdrive1]

This is an example of partial capping on my Daytona..I personally thought it was a clean job, but it's a basic one color, I could only imagine if it was a typical Eliminator 5 to 7 color combo.
Just the front and rear are done, with a one piece stainless rub rail down he side. Clean

Is your boat at Tank It? Getting set up for center steer?

 

[UAV.Pilot]

Is your boat at Tank It? Getting set up for center steer?

Yeah sure is, it's being built by Brian, and Joe 555Racing...👍
We're going all out for the Enduro 336...

 

[shueman]

Yeah sure is, it's being built by Brian, and Joe 555Racing...
We're going all out for the Enduro 336...

Nice job ... :thumbsup

 

[AZMIDLYF]

That looks like a fun project.

 

[Eliminator Boats]

Boat is rigged and coming back to Eliminator Wed or Thu for hatch fabrication and interior install ... :thumbsup

 

[AZMIDLYF]

Looks like it will be lacking motivation. :rolleyes

I might be blind but where do those pipes exit?

 

[rivrrts429]

There is some money in that pump. B1 builds some sano stuff [emoji106]

 

[JordanDangerfield]

Looks like it will be lacking motivation. :rolleyes

I might be blind but where do those pipes exit?

I don't think the holes have been cut yet.

 

[Flying_Lavey]

Looks like it will be lacking motivation. :rolleyes

I might be blind but where do those pipes exit?

That's the new EGR system. Lol!

 

[Jed-O]

Boat is rigged and coming back to Eliminator Wed or Thu for hatch fabrication and interior install ... :thumbsup

View attachment 473077

:thumbsup

 

[Eliminator Boats]

Update pix ... start interior install tomorrow.

 

[Andy01]

Looks great, looking forward to seeing the finished project. :thumbsup

 

[shueman]

:thumbsup

 

[rivrrts429]

Ho-Lee-Fuk Gary! You guys knocked this one out of the park.

Eliminator & B1 raising the bar.

 

[AZMIDLYF]

Someone's boating season is getting off to a great start!! Nicely done sir.

 

[Abc123]

Tom Cowle's 21' Daytona is out on the rigging floor and will be heading to GS Marine soon for the pump modifications.
Ordering all the gauges, etc. next week and will start cutting holes when Greg sends it back.

I wish my floors looked like that. What it cost to get them redone like that, in a 19'?

 

[Abc123]

:thumbsup

Insane! Any more close up of the interior and rigging? How much power does that engine make? Looks like Chris at B1 did some really bitchen work (not abnormal). Lower river boat?

 

[Outdrive1]

Gangster

 

[Gelcoater]

Insane! Any more close up of the interior and rigging? How much power does that engine make? Looks like Chris at B1 did some really bitchen work (not abnormal). Lower river boat?

How much power?
Refer to post 31

"Enough"

 

[Jmp]

Insane! Any more close up of the interior and rigging? How much power does that engine make? Looks like Chris at B1 did some really bitchen work (not abnormal). Lower river boat?

I was talking to the owners kid about the build when I was in there when my interior was getting redone and he told me it was making 1100hp. 588" with an 8 71 sitting on top

 

[Gelcoater]

I was talking to the owners kid about the build when I was in there when my interior was getting redone and he told me it was making 1100hp. 588" with an 8 71 sitting on top

I think that kid sandbagged your ass.

 

[Jmp]

I think that kid sandbagged your ass.

More than 1100?