Leaking Trim Pump Reservoir

[farmo83]

So I opened my boat up this past weekend to find the bilge full of fluid from my beloved trim pump. I?m thinking my reservoir leaking based on the following.

1.It leaked over the winter when pump wasn?t working
2.The amount of fluid that leaked out far exceeds what those hoses could hold
3. Also I would think if the hydraulic hoses had lost all fluid the outdrive would fall to the ground?

Are these reservoir?s leaking a common issue ?

So to fix this is this something I need to get a whole new pump or can just get a new reservoir? I?ve thought of taking the reservoir off, finding the leak and epoxying it as well

 

[Headless hula]

I bought a new reservoir. It's machined aluminum and clear acrylic. Ran right around 200 bucks, but no more Exxon valdez bilge....

 

[getreal]

I have Billet ones.
I sell the tank only (and cap) for $209.95
You can get them in a "Left or Right"

 

[TrojanDan]

Happened on our boat. I believe Absolute replaced just the plastic reservoir. Common problem.

 

[Riley1]

I had to replace the reservoir on mine last year. 4 screws and an o-ring.

 

[Headless hula]

I have Billet ones.
I sell the tank only (and cap) for $209.95
You can get them in a "Left or Right"

That's the one I bought, and it's gorgeous.

 

[RiverDave]

Pretty common for the tanks to crack.

 

[Ballyhoo]

I had to replace the reservoir on mine last year. 4 screws and an o-ring.

Older post but I need to replace my reservoir tank. It has the 4 screws on top. Is it a straight forward replacement? Just take out the four screws, replace o ring and new reservoir? Do I need to take the whole assembly out or can I replace it without removing the whole assembly? (motor and reservoir) Thanks

 

[Riley1]

Older post but I need to replace my reservoir tank. It has the 4 screws on top. Is it a straight forward replacement? Just take out the four screws, replace o ring and new reservoir? Do I need to take the whole assembly out or can I replace it without removing the whole assembly? (motor and reservoir) Thanks

It’s been awhile. But I’m fairly sure that it was a straight forward swap. I know for certain that I did it in the bilge and did not remove the pump.

 

[ka0tyk]

Older post but I need to replace my reservoir tank. It has the 4 screws on top. Is it a straight forward replacement? Just take out the four screws, replace o ring and new reservoir? Do I need to take the whole assembly out or can I replace it without removing the whole assembly? (motor and reservoir) Thanks

its a simple swap with the 4 screws, but there is a tube that goes down into the bottom of the reservoir, if its mounted low like in the above picture, you'll probably have to unbolt/unscrew it from the transom (some are mounted onto a plate that mounts to the floor...) in order to actually get the old tank off and put the new one on.

 

[Ballyhoo]

its a simple swap with the 4 screws, but there is a tube that goes down into the bottom of the reservoir, if its mounted low like in the above picture, you'll probably have to unbolt/unscrew it from the transom (some are mounted onto a plate that mounts to the floor...) in order to actually get the old tank off and put the new one on.

Thanks to both of you for the quick replies.

 

[MagicMan]

I replaced my trim pump reservoir last season, no more leaks. Putting boat away last weekend and found leak is back. Could not see anything leaking on pump hoses or immediate area. Could ir be the reservoir again ??

 

[Havasu Catman]

I replaced my trim pump reservoir last season, no more leaks. Putting boat away last weekend and found leak is back. Could not see anything leaking on pump hoses or immediate area. Could ir be the reservoir again ??

It can be leaking from the reservoir or the back of the pump. If you take the 2 3/8 bolts off the back of the bracket you can separate the pump and reservoir from the bracket. There are 2 plugs on the back side of the pump that leak. They are not serviceable and the pump will need to be replaced. When they leak it runs down onto the reservoir and makes you think the reservoir is leaking but in reality it is higher up.

 

[MagicMan]

It can be leaking from the reservoir or the back of the pump. If you take the 2 3/8 bolts off the back of the bracket you can separate the pump and reservoir from the bracket. There are 2 plugs on the back side of the pump that leak. They are not serviceable and the pump will need to be replaced. When they leak it runs down onto the reservoir and makes you think the reservoir is leaking but in reality it is higher up.

Thanks for the advice, gonna check it out when I'm out there next week. Where can I get a new pump in havasu am I better off ordering now?

 

[colenighthawk]

Thanks for the advice, gonna check it out when I'm out there next week. Where can I get a new pump in havasu am I better off ordering now?

Thanks for the advice, gonna check it out when I'm out there next week. Where can I get a new pump in havasu am I better off ordering now?

I know this is an old tread, but my trim pump started leaking from the same spot I think. I've replaced the plastic reservoir and no change. How much the pump cost and where did you ended up getting it from.
Thsnks

 

[ChrisV]

I know this is an old tread, but my trim pump started leaking from the same spot I think. I've replaced the plastic reservoir and no change. How much the pump cost and where did you ended up getting it from.
Thsnks

https://www.amazon.com/DB-Electrical-TRM0027-Mercruiser-18-6769-1/dp/B019GUK21G/ref=sr_1_4?crid=3FW27MMPHTX91&dib=eyJ2IjoiMSJ9.6ccBSJo7gKFO9UexG9QRz53bWBgc-kjzKS180kavR4l1gKgl_F15O6gdnoS0xo40Hxrac51n06QEpFjhpkXaS_N_33CmzL0m7u7_QuJabhe2k4A99pm78f6-n9wobYrw-7WzYRITSFovuCrB-biBogyAStG3Yz7RnYxQRK_LS-ATWkGODHqT3QzSSAzN-vWUyxP-DQDiU6O6Bgx3BM2JtGKhjcgy8wiFfS4PCVJv7YY.cLJ1y7T5mTOVPAY8RZwo2D3uTrH_8ZYEHxm2I2-KWok&dib_tag=se&keywords=sae+j1171+marine+trim+pump&qid=1709273871&sprefix=sae+j1171+trim%2Caps%2C141&sr=8-4

Mercury Hi-Flow Trim Tilt Pump Unit | Buckshot Racing #77

Mercury Hi-Flow Trim Tilt Unit complete assembly with 3-wire connection, High Volume Marine Pump, SAE J1171 Motor, two 1/4" and one 5/16” Ring Terminal Ends, with the Mercury Racing-style 3.5" Steel Fluid Reservoir. Also included are stout-upgraded #3 inverted flair fittings that fit the factory...

www.buckshotracing77.com

 

[BDC Coatings]

I had to replace the reservoir on mine last year. 4 screws and an o-ring.

Mine has a leak also. I will try an o ring and tank. The tank seems it has a small dip around the top edge towards the back of the tank. Sae J1171. On a 2022 boat. Would you have a favorite place to up grade and or purchase these items ?

 

[DWC]

This thread is so old I figured someone complaining about Ultra revived it..

Sorry @BDC Coatings

Where is it stored?

 

[BDC Coatings]

This boat is stored in Texas in my shop. The boat has 25 hrs on it 2022 Howard Sport Deck 288

 

[evantwheeler]

Mine has a leak also. I will try an o ring and tank. The tank seems it has a small dip around the top edge towards the back of the tank. Sae J1171. On a 2022 boat. Would you have a favorite place to up grade and or purchase these items ?

You can get them reasonably priced on Ebay. I just bought one, paid $45 shipped w/ tax for the Quicksilver kit. I always find someone with OEM parts that will accept offers and shoot them an offer.

883166a2 for sale | eBay

Get the best deals for 883166a2 at eBay.com. We have a great online selection at the lowest prices with Fast & Free shipping on many items!

www.ebay.com

 

[DWC]

This boat is stored in Texas in my shop. The boat has 25 hrs on it 2022 Howard Sport Deck 288

Is it climate controlled. Mine seem to take a beating in our storage. Neighbor/inmate says the storage unit is like an easy bake oven.

 

[Bowtiepower00]

I know this is an old thread, but I had the same issue on my Lavey. In addition to the large o-ring on the reservoir, there is a small o-ring on the bottom bolt that holds the reservoir to the pump. The caps are also known to leak, there is an updated part number for the cap. Replacing the o-rings and the cap fixed the issue on my boat.

 

[BDC Coatings]

You can get them reasonably priced on Ebay. I just bought one, paid $45 shipped w/ tax for the Quicksilver kit. I always find someone with OEM parts that will accept offers and shoot them an offer.

883166a2 for sale | eBay

Get the best deals for 883166a2 at eBay.com. We have a great online selection at the lowest prices with Fast & Free shipping on many items!

www.ebay.com

Thank you. Just ordered one

 

[ChrisV]

I have Billet ones.
I sell the tank only (and cap) for $209.95
You can get them in a "Left or Right"

Old thread but who makes this?