Havasu machine shop

[Rajobigguy]

Any recommendation for a shop in Havasu that can do a power hone with a torque plate?

 

[mjc]

check with S.A.M machining. Mike 928-733-8073. He has been doing all my work recently.

 

[Rajobigguy]

check with S.A.M machining. Mike 928-733-8073. He has been doing all my work recently.

Thanks, will do. I’m trying to establish a new vendor list to support my hobbies.

 

[warpt71]

JD Machine #(928) 855-1411

Mike sold the business but I have heard that the new owners are doing well. I have not taken anything in to the new owners yet..........

 

[mjc]

JD Machine #(928) 855-1411

Mike sold the business but I have heard that the new owners are doing well. I have not taken anything in to the new owners yet..........

JD is who sent me to SAM when they couldn't even do a valve job for me.

 

[SummitKarl]

Unfortunately JD machine is all but gone

Try Dave at the Carquest....yes car quest has a machine shop in the back

 

[Rajobigguy]

Unfortunately JD machine is all but gone

Try Dave at the Carquest....yes car quest has a machine shop in the back

I've been to their machine shop and while it's fine for normal everyday driver type engine, they lack the equipment to do a real precession honing job. I actually have much of the same equipment that they have.

 

[guest hs]

I use Todd at Todd’s Performance Engines in Havasu

 

[Ace in the Hole]

Unfortunately JD machine is all but gone

Try Dave at the Carquest....yes car quest has a machine shop in the back

Have taken more than one set of heads to him, as well as had him do some jet ski bore work, as well as a flywheel. Super nice guy and fair.

 

[SummitKarl]

Have taken more than one set of heads to him, as well as had him do some jet ski bore work, as well as a flywheel. Super nice guy and fair.

exactly!!! he does custom a/c and pwr steering lines as well

 

[Rajobigguy]

exactly!!! he does custom a/c and pwr steering lines as well

Dave does fine work and has indeed helped me out adapting lines for custom lines and such. If I were rebuilding a stock engine for a pick up our street driven vehicle I would have no problem taking that kind of job to him but this isn't that kind of engine. What I'm looking for is someone with a CK10 Sunnen (or equivilent) to do a precession hone job with a torque plate.

 

[SummitKarl]

Dave does fine work and has indeed helped me out adapting lines for custom lines and such. If I were rebuilding a stock engine for a pick up our street driven vehicle I would have no problem taking that kind of job to him but this isn't that kind of engine. What I'm looking for is someone with a CK10 Sunnen (or equivilent) to do a precession hone job with a torque plate.

go to Facebook group "Mohave County Drag Racing Association" and post your question.................https://www.facebook.com/groups/609676789232701

 

[cncman1]

Try R&D Dyno & Machine, on Acoma blvd

 

[PRIMO]

Todd's Performance / Usually where everyone Ends up in Havasu if you want a shop that gets after it ........

 

[PRORACER7474]

Sureway Automotive and Machine in Kingman

 

[She's Mine]

I've had work done at Todd's Performance before and it was good but recently the quality isn't living up to the reputation. Had a hone and re-ring end up with 40% leak down. There are many shops you can choose from GT Performance, Teague Custom Marine, Bostic, etc. Maybe driving a little further would save you time and money in the future.

 

[RIVERBORN]

Teague will do any motor work, or at least they used too. Not just dcbs and extreme shit.
Just be prepared to have it done correctly. I can’t remember off hand of the machine work cost. but it wasn’t crazy expensive, but they need your pistons also.

 

[NicPaus]

This thread is 2 years old... But I have not seen @SummitKarl posting for a while. Hopefully he is just busy drawing up plans and enjoying life.

 

[Bakotrash]

Sureway Automotive and Machine in Kingman

This is where most people in Vegas take there stuff now. Nice people and good work I hear.

 

[JFMFG]

I've had work done at Todd's Performance before and it was good but recently the quality isn't living up to the reputation. Had a hone and re-ring end up with 40% leak down. There are many shops you can choose from GT Performance, Teague Custom Marine, Bostic, etc. Maybe driving a little further would save you time and money in the future.

Don’t say that Todd’s just did my stuff lol. Don’t send those vibes my way lol

 

[She's Mine]

Don’t say that Todd’s just did my stuff lol. Don’t send those vibes my way lol

Good vibes always brother. Never want or wish for someone to go through what I go through. lol